SCHNEIDER
variable speed drive ATV12 - 0.37kW - 0.55hp - 200..240V - 1ph - with heat sink - ATV12H037M2
ATV12H037M2
€186.36 Excl. Tax
€223.63 Inc. Tax
Excl. Tax
Excl. Tax
Incl. Tax
Incl. Tax
You save
In stock – Dispatched within 24/48h
- Technical support and dedicated single point of contact
- Free delivery from 200€ of purchase (Metropolitan France)
- 100% secure payments
Technical informations
| Product destination: | Asynchronous motors |
|---|---|
| Component name: | ATV12 |
| Built-in fan: | Without |
| Network number of phases: | 1 phase |
| Motor power kW: | 0.37 kW |
| Motor power hp: | 0.55 hp |
| Line current: | 5.9 A at 200 V4.9 A at 240 V |
| Speed range: | 1...20 |
| IP degree of protection: | IP20 without blanking plate on upper part |
| Range of product: | Altivar 12 |
| Product or component type: | Variable speed drive |
| Product specific application: | Simple machine |
| Communication port protocol: | Modbus |
| [Us] rated supply voltage: | 200...240 V - 15...10 % |
| EMC filter: | Integrated |
| Supply frequency: | 50/60 Hz +/- 5 % |
|---|---|
| Connector type: | 1 RJ45 (on front face) for Modbus |
| Physical interface: | 2-wire RS 485 for Modbus |
| Transmission frame: | RTU for Modbus |
| Transmission rate: | 4800 bit/s9600 bit/s19200 bit/s38400 bit/s |
| Number of addresses: | 1...247 for Modbus |
| Communication service: | Read holding registers (03) 29 wordsWrite single register (06) 29 wordsWrite multiple registers (16) 27 wordsRead/write multiple registers (23) 4/4 wordsRead device identification (43) |
| Continuous output current: | 2.4 A at 4 kHz |
| Maximum transient current: | 3.6 A for 60 s |
| Speed drive output frequency: | 0.5...400 Hz |
| Braking torque: | Up to 70 % of nominal motor torque without braking resistor |
| Output voltage: | 200...240 V 3 phases |
| Electrical connection: | Terminal, clamping capacity: 3.5 mm², AWG 12 (L1, L2, L3, U, V, W, PA, PC) |
| Tightening torque: | 0.8 N.m |
| Insulation: | Electrical between power and control |
| Supply: | Internal supply for reference potentiometer: 5 V DC (4.75...5.25 V), Internal supply for logic inputs: 24 V DC (20.4...28.8 V), |
| Analogue input type: | Configurable current AI1 0...20 mA 250 OhmConfigurable voltage AI1 0...10 V 30 kOhmConfigurable voltage AI1 0...5 V 30 kOhm |
| Discrete input type: | Programmable LI1...LI4 24 V 18...30 V |
| Discrete input logic: | Negative logic (sink), > 16 V (state 0), Positive logic (source), 0... 11 V (state 1) |
| Sampling duration: | 20 ms, tolerance +/- 1 ms for logic input10 ms for analogue input |
| Linearity error: | +/- 0.3 % of maximum value for analogue input |
| Analogue output type: | AO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bitsAO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits |
| Discrete output type: | Logic output LO+, LO-Protected relay output R1A, R1B, R1C 1 C/O |
| Minimum switching current: | 5 mA at 24 V DC for logic relay |
| Maximum switching current: | 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay |
| Braking to standstill: | By DC injection, |
| Frequency resolution: | Analog input: converter A/D, 10 bitsDisplay unit: 0.1 Hz |
| Time constant: | 20 ms +/- 1 ms for reference change |
| Functionality: | Basic |
| Specific application: | Commercial equipment |
| Discrete and process manufacturing: | Commercial equipment MixerCommercial equipment Other applicationTextile Ironing |
| Power range: | 0...0.5 kW at 200...240 V 1 phase |
| Motor starter type: | Variable speed drive |
| Discrete input number: | 4 |
| Discrete output number: | 2 |
| Analogue input number: | 1 |
| Analogue output number: | 1 |
| Asynchronous motor control profile: | Sensorless flux vector controlVoltage/frequency ratio (V/f)Quadratic voltage/frequency ratio |
| Transient overtorque: | 150...170 % of nominal motor torque depending on drive rating and type of motor |
| Acceleration and deceleration ramps: | Linear from 0 to 999.9 sSU |
| Motor slip compensation: | AdjustablePreset in factory |
| Switching frequency: | 2...16 kHz adjustable4...16 kHz with derating factor |
| Nominal switching frequency: | 4 kHz |
| Prospective line Isc: | 1 kA |
| Protection type: | Line supply overvoltageLine supply undervoltageOvercurrent between output phases and earthOverheating protectionShort-circuit between motor phasesAgainst input phase loss in three-phaseThermal motor protection via the drive by continuous calculation of I²t |
| Quantity per set: | Set of 1 |
| Width: | 72 mm |
| Height: | 143 mm |
| Depth: | 121.2 mm |
| Product weight: | 0.7 kg |
In short
Reference ATV12H037M2
Product Name variable speed drive ATV12 - 0.37kW - 0.55hp - 200..240V - 1ph - with heat sink - ATV12H037M2
Related Categories
