SCHNEIDER
variable speed drive ATV312 - 15kW - 32kVA - 492 W - 380..500 V - 3-phase supply - ATV312HD15N4
ATV312HD15N4
Obsolete product, here is the proposed substitution for the reference ATV312HD15N4 : ATV320D15N4C
Technical informations
| Range of product: | Altivar 312 |
|---|---|
| Product or component type: | Variable speed drive |
| Product destination: | Asynchronous motors |
| Product specific application: | Simple machine |
| Assembly style: | With heat sink |
| Component name: | ATV312 |
| Motor power kW: | 15 kW |
| Motor power hp: | 20 hp |
| [Us] rated supply voltage: | 380...500 V - 15...10 % |
| Supply frequency: | 50...60 Hz - 5...5 % |
| Network number of phases: | 3 phases |
| Line current: | 48.2 A at 380 V, Isc = 22 kA36.8 A at 500 V |
| EMC filter: | Integrated |
| Apparent power: | 32 kVA |
| Maximum transient current: | 49.5 A for 60 s |
| Power dissipation in W: | 492 W at nominal load |
| Speed range: | 1...50 |
| Asynchronous motor control profile: | Sensorless flux vector control with PWM type motor control signalFactory set |
| Electrical connection: | Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5 mm² AWG 14L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 25 mm² AWG 3 |
| Supply: | Internal supply for logic inputs: 19...30 V 100 mA, protection type: overload and short-circuit protectionInternal supply for reference potentiometer (2.2 to 10 kOhm): 10...10.8 V 10 mA, protection type: overload and short-circuit protection |
| Communication port protocol: | ModbusCANopen |
| IP degree of protection: | IP20 on upper part without cover plateIP21 on connection terminalsIP31 on upper partIP41 on upper part |
| Option card: | Communication card for CANopen daisy chainCommunication card for DeviceNetCommunication card for FipioCommunication card for Modbus TCPCommunication card for Profibus DP |
| Supply voltage limits: | 323...550 V |
|---|---|
| Prospective line Isc: | 22 kA |
| Continuous output current: | 33 A at 4 kHz |
| Output frequency: | 0...500 Hz |
| Nominal switching frequency: | 4 kHz |
| Switching frequency: | 2...16 kHz adjustable |
| Transient overtorque: | 170...200 % of nominal motor torque |
| Braking torque: | 150 % during 60 s with braking resistor100 % with braking resistor continuously150 % without braking resistor |
| Regulation loop: | Frequency PI regulator |
| Motor slip compensation: | AdjustableAutomatic whatever the loadSuppressable |
| Output voltage: | |
| Tightening torque: | Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6: 0.6 N.mL1, L2, L3, U, V, W, PA, PB, PA/+, PC/-: 4.5 N.m |
| Insulation: | Electrical between power and control |
| Analogue input number: | 3 |
| Analogue input type: | AI1 configurable voltage 0...10 V, input voltage 30 V max, impedance: 30000 OhmAI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance: 30000 OhmAI3 configurable current 0...20 mA, impedance: 250 Ohm |
| Sampling duration: | AI1, AI2, AI3: 8 ms analogLI1...LI6: 4 ms discrete |
| Response time: | AOV, AOC 8 ms for analogR1A, R1B, R1C, R2A, R2B 8 ms for discrete |
| Linearity error: | +/- 0.2 % for output |
| Analogue output number: | 1 |
| Analogue output type: | AOC configurable current: 0...20 mA, impedance: 800 Ohm, resolution: 8 bitsAOV configurable voltage: 0...10 V, impedance: 470 Ohm, resolution: 8 bits |
| Discrete input logic: | Logic input not wired (LI1...LI4), Negative logic (source) (LI1...LI6), > 19 V (state 0)Positive logic (source) (LI1...LI6), 11 V (state 1) |
| Discrete output number: | 2 |
| Discrete output type: | Configurable relay logic: (R1A, R1B, R1C) 1 NO + 1 NC - 100000 cyclesConfigurable relay logic: (R2A, R2B) NC - 100000 cycles |
| Minimum switching current: | R1-R2 10 mA at 5 V DC |
| Maximum switching current: | R1-R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 msR1-R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 msR1-R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 msR1-R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms |
| Discrete input number: | 6 |
| Discrete input type: | (LI1...LI6) programmable at 24 V, 0...100 mA for PLC, impedance: 3500 Ohm |
| Acceleration and deceleration ramps: | S, U or customizedLinear adjustable separately from 0.1 to 999.9 s |
| Braking to standstill: | By DC injection |
| Protection type: | Input phase breaks: driveLine supply overvoltage and undervoltage safety circuits: driveLine supply phase loss safety function, for three phases supply: driveMotor phase breaks: driveOvercurrent between output phases and earth (on power up only): driveOverheating protection: driveShort-circuit between motor phases: driveThermal protection: motor |
| Insulation resistance: | >= 500 mOhm 500 V DC for 1 minute |
| Local signalling: | 1 LED (red) for drive voltageFour 7-segment display units for CANopen bus status |
| Time constant: | 5 ms for reference change |
| Frequency resolution: | Analog input: 0.1...100 HzDisplay unit: 0.1 Hz |
| Connector type: | 1 RJ45 for Modbus/CANopen |
| Physical interface: | RS485 multidrop serial link |
| Transmission frame: | RTU |
| Transmission rate: | 10, 20, 50, 125, 250, 500 kbps or 1 Mbps for CANopen4800, 9600 or 19200 bps for Modbus |
| Number of addresses: | 1...127 for CANopen1...247 for Modbus |
| Number of drive: | 127 for CANopen31 for Modbus |
| Marking: | CE |
| Operating position: | Vertical +/- 10 degree |
| Outer dimension: | 390 x 245 x 190 mm595 x 234 x 268 mm330 x 245 x 190 mm |
| Height: | 329.5 mm |
| Width: | 245 mm |
| Depth: | 192 mm |
| Product weight: | 11 kg |
| Network frequency: | 47.5...63 Hz |
In short
Reference ATV312HD15N4
Product Name variable speed drive ATV312 - 15kW - 32kVA - 492 W - 380..500 V - 3-phase supply - ATV312HD15N4
Related Categories